CPU: AMCC PowerPC 460EX Rev. A at 800 MHz (PLB=200, OPB=100, EBC=100 MHz) Security/Kasumi support Bootstrap Option B - Boot ROM Location EBC (16 bits) Internal PCI arbiter disabled 32 kB I-Cache 32 kB D-Cache Board: Canyonlands - AMCC PPC460EX Evaluation Board, 2*PCIe, Rev. 14 I2C: ready DTT: 1 is 48 C DRAM: 512 MB (ECC not enabled, 400 MHz, CL3) FLASH: 64 MB NAND: 128 MiB PCI: Bus Dev VenId DevId Class Int PCIE0: link is not up. PCIE0: initialization as root-complex failed PCIE1: successfully set as root-complex 02 00 1000 0056 0100 00 01 00 aaa1 bed1 0604 00 Net: ppc_4xx_eth0, ppc_4xx_eth1 Type run flash_nfs to mount root filesystem over NFS Hit any key to stop autoboot: 0 => pci 1 Scanning PCI devices on bus 1 BusDevFun VendorId DeviceId Device Class Sub-Class _____________________________________________________________ 01.00.00 0xaaa1 0xbed1 Bridge device 0x04 => pci 2 Scanning PCI devices on bus 2 BusDevFun VendorId DeviceId Device Class Sub-Class _____________________________________________________________ 02.00.00 0x1000 0x0056 Mass storage controller 0x00 => run net_nfs Waiting for PHY auto negotiation to complete.. done ENET Speed is 100 Mbps - FULL duplex connection (EMAC0) Using ppc_4xx_eth0 device TFTP from server 10.38.12.201; our IP address is 10.38.12.229 Filename 'canyonlands/uImage'. Load address: 0x400000 Loading: ################################################################# ############################ done Bytes transferred = 1352171 (14a1eb hex) ENET Speed is 100 Mbps - FULL duplex connection (EMAC0) Using ppc_4xx_eth0 device TFTP from server 10.38.12.201; our IP address is 10.38.12.229 Filename 'canyonlands/canyonlands.dtb'. Load address: 0xfc1e0000 Loading: # done Bytes transferred = 12288 (3000 hex) ## Booting kernel from Legacy Image at 00400000 ... Image Name: Linux-2.6.26 Created: 2008-10-31 10:38:58 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1352107 Bytes = 1.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK ## Flattened Device Tree blob at fc1e0000 Booting using the fdt blob at 0xfc1e0000 Loading Device Tree to 007fc000, end 007ff188 ... OK Using Canyonlands machine description Linux version 2.6.26 (tuan@Saigon) (gcc version 4.0.0 (DENX ELDK 4.1 4.0.0)) #2 Fri Oct 31 17:38:56 ICT 2008 Zone PFN ranges: DMA 0 -> 131072 Normal 131072 -> 131072 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 131072 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: root=/dev/nfs rw nfsroot=10.38.12.201:/opt/eldk/ppc_4xxFP ip=10.38.12.229:10.38.12.201:10.38.12.1:255.255.252.0:canyonlands:eth0:off panic=1 console=ttyS0,115200 UIC0 (32 IRQ sources) at DCR 0xc0 UIC1 (32 IRQ sources) at DCR 0xd0 UIC2 (32 IRQ sources) at DCR 0xe0 UIC3 (32 IRQ sources) at DCR 0xf0 PID hash table entries: 2048 (order: 11, 8192 bytes) clocksource: timebase mult[500000] shift[22] registered Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 516608k/524288k available (2648k kernel code, 7440k reserved, 112k data, 128k bss, 148k init) SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Mount-cache hash table entries: 512 net_namespace: 192 bytes NET: Registered protocol family 16 256k L2-cache enabled PCIE0: Checking link... PCIE0: No device detected. PCI host bridge /plb/pciex@d00000000 (primary) ranges: MEM 0x0000000e00000000..0x0000000e7fffffff -> 0x0000000080000000 IO 0x0000000f80000000..0x0000000f8000ffff -> 0x0000000000000000 4xx PCI DMA offset set to 0x00000000 PCIE0: successfully set as root-complex PCIE1: Checking link... PCIE1: Device detected, waiting for link... PCIE1: link is up ! PCI host bridge /plb/pciex@d20000000 (primary) ranges: MEM 0x0000000e80000000..0x0000000effffffff -> 0x0000000080000000 IO 0x0000000f80010000..0x0000000f8001ffff -> 0x0000000000000000 4xx PCI DMA offset set to 0x00000000 PCIE1: successfully set as root-complex PCI host bridge /plb/pci@c0ec00000 (primary) ranges: MEM 0x0000000d80000000..0x0000000dffffffff -> 0x0000000080000000 IO 0x0000000c08000000..0x0000000c0800ffff -> 0x0000000000000000 4xx PCI DMA offset set to 0x00000000 PCI: Probing PCI hardware PCI: Hiding 4xx host bridge resources 0000:40:00.0 PCI: Hiding 4xx host bridge resources 0001:80:00.0 PCI: Bridge: 0000:40:00.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0001:80:00.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. SCSI subsystem initialized NET: Registered protocol family 2 IP route cache hash table entries: 16384 (order: 4, 65536 bytes) TCP established hash table entries: 65536 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 65536 bind 65536) TCP reno registered NET: Registered protocol family 1 msgmni has been set to 1009 io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered assign_interrupt_mode Found MSI capability assign_interrupt_mode Found MSI capability aer: probe of 0000:40:00.0:pcie01 failed with error -38 aer: probe of 0001:80:00.0:pcie01 failed with error -38 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 18) is a 16550A console [ttyS0] enabled serial8250.0: ttyS1 at MMIO 0x4ef600400 (irq = 19) is a 16550A serial8250.0: ttyS2 at MMIO 0x4ef600500 (irq = 29) is a 16550A serial8250.0: ttyS3 at MMIO 0x4ef600600 (irq = 20) is a 16550A 4ef600300.serial: ttyS0 at MMIO 0x4ef600300 (irq = 18) is a 16550A 4ef600400.serial: ttyS1 at MMIO 0x4ef600400 (irq = 19) is a 16550A 4ef600500.serial: ttyS2 at MMIO 0x4ef600500 (irq = 29) is a 16550A 4ef600600.serial: ttyS3 at MMIO 0x4ef600600 (irq = 20) is a 16550A brd: module loaded PPC 4xx OCP EMAC driver, version 3.54 MAL v2 /plb/mcmal, 2 TX channels, 16 RX channels ZMII /plb/opb/emac-zmii@ef600d00 initialized RGMII /plb/opb/emac-rgmii@ef601500 initialized with MDIO support TAH /plb/opb/emac-tah@ef601350 initialized TAH /plb/opb/emac-tah@ef601450 initialized /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:10:ec:00:f9:f6 eth0: found Generic MII PHY (0x00) /plb/opb/emac-rgmii@ef601500: input 1 in RGMII mode eth1: EMAC-1 /plb/opb/ethernet@ef600f00, MAC 00:10:ec:80:f9:f6 eth1: found Generic MII PHY (0x01) Fusion MPT base driver 3.04.06 Copyright (c) 1999-2007 LSI Corporation Fusion MPT SPI Host driver 3.04.06 Fusion MPT FC Host driver 3.04.06 Fusion MPT SAS Host driver 3.04.06 Fusion MPT misc device (ioctl) driver 3.04.06 mptctl: Registered with Fusion MPT base driver mptctl: /dev/mptctl @ (major,minor=10,220) TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. eth0: link is down IP-Config: Complete: device=eth0, addr=10.38.12.229, mask=255.255.252.0, gw=10.38.12.1, host=canyonlands, domain=, nis-domain=(none), bootserver=10.38.12.201, rootserver=10.38.12.201, rootpath= Looking up port of RPC 100003/2 on 10.38.12.201 eth0: link is up, 100 FDX, pause enabled Looking up port of RPC 100005/1 on 10.38.12.201 VFS: Mounted root (nfs filesystem). Freeing unused kernel memory: 148k init modprobe: FATAL: Could not load /lib/modules/2.6.26/modules.dep: No such file or directory modprobe: FATAL: Could not load /lib/modules/2.6.26/modules.dep: No such file or directory INIT: version 2.85 booting Welcome to DENX Embedded Linux Environment Press 'I' to enter interactive startup. Building the cache [ OK ] storage network audio done[ OK ] modprobe: FATAL: Could not load /lib/modules/2.6.26/modules.dep: No such file or directory Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Setting clock : Thu Jan 1 00:00:05 UTC 1970 [ OK ] Setting hostname canyonlands: [ OK ] Mounting local filesystems: [ OK ] Enabling swap space: [ OK ] INIT: Entering runlevel: 3 Entering non-interactive startup Bringing up loopback interface: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Starting portmap: [ OK ] Mounting NFS filesystems: [ OK ] Mounting other filesystems: [ OK ] Starting xinetd: [ OK ] DENX ELDK version 4.1 build 2007-01-19 Linux 2.6.26 on a ppc canyonlands login: root Last login: Sat Jul 12 02:53:28 on console bash-3.00# uname -r 2.6.26 bash-3.00# lspci 40:00.0 PCI bridge: Unknown device aaa0:bed0 (rev 01) 80:00.0 PCI bridge: Unknown device aaa1:bed1 (rev 01) bash-3.00# cat /proc/interrupts CPU0 18: 252 UIC Level serial 21: 6032 UIC Level MAL TX EOB 22: 11737 UIC Level MAL RX EOB 23: 0 UIC Edge L2C 24: 0 UIC Level MAL SERR 25: 0 UIC Level MAL TX DE 26: 0 UIC Level MAL RX DE 27: 0 UIC Level EMAC BAD: 0 bash-3.00# cat /proc/devices Character devices: 1 mem 2 pty 3 ttyp 4 ttyS 5 /dev/tty 5 /dev/console 5 /dev/ptmx 10 misc 21 sg 128 ptm 136 pts Block devices: 1 ramdisk bash-3.00#