Hi every one<br><br>I had used kernel of ELDK 3.1.1 and Ramdisk of ELDK 4.0 on board MPC8xxL .It run ok but I see it will meet trouble :D<br>When I use kernel and Ramdisk of ELDK 3.1.1 for MPC8xxL (I only rebuild Kernel use oldconfig and use uRamdisk in source (not rebuild )) but I receive error<br>////////////////////////////////////////////////////////////////////////////<br>Bootm 40040000 40400000 ## Booting image at 40040000 ...<br> Image Name: Linux-2.4.25<br> Created: 2006-11-06 12:51:51 UTC<br> Image Type: PowerPC Linux Kernel Image (gzip compressed)<br> Data Size: 712087 Bytes = 695.4 kB<br> Load Address: 00000000<br> Entry Point: 00000000<br> Verifying Checksum ... OK<br> Uncompressing Kernel Image ... OK<br>## Loading RAMDisk Image at 40400000 ...<br> Image Name:
Simple Embedded Linux Framework<br> Created: 2005-06-07 12:59:15 UTC<br> Image Type: PowerPC Linux RAMDisk Image (gzip compressed)<br> Data Size: 1625993 Bytes = 1.6 MB<br> Load Address: 00000000<br> Entry Point: 00000000<br> Verifying Checksum ... OK<br> Loading Ramdisk to 00e1f000, end 00fabf89 ... OK<br>Linux version 2.4.25 (root@main) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3.3-10)) #1 Mon Nov 6 19:50:02 ICT 2006<br><br>On node 0 totalpages: 4096<br><br>zone(0): 4096 pages.<br><br>zone(1): 0 pages.<br><br>zone(2): 0 pages.<br><br>Kernel command line: <br><br>Decrementer Frequency = 300000000/60<br><br>Calibrating delay loop... 79.66 BogoMIPS<br><br>Memory: 12912k available (1212k kernel code, 408k data, 56k init, 0k highmem)<br><br>Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)<br><br>Inode cache
hash table entries: 1024 (order: 1, 8192 bytes)<br><br>Mount cache hash table entries: 512 (order: 0, 4096 bytes)<br><br>Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)<br><br>Page-cache hash table entries: 4096 (order: 2, 16384 bytes)<br><br>POSIX conformance testing by UNIFIX<br><br>Linux NET4.0 for Linux 2.4<br><br>Based upon Swansea University Computer Society NET3.039<br><br>Initializing RT netlink socket<br><br>Starting kswapd<br><br>JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.<br><br>CPM UART driver version 0.04<br><br>ttyS0 at 0x0280 is on SMC1 using BRG1<br><br>ttyS1 at 0x0380 is on SMC2 using BRG2<br><br>pty: 256 Unix98 ptys configured<br><br>Status LED driver $Revision: 1.0 $ initialized<br><br>eth0: CPM ENET Version 0.2 on SCC1, 00:d0:93:0e:7b:d2<br><br>eth1: FEC ENET Version 0.3, FEC irq 9, with MDIO, MII irq 12, addr 00:d0:93:0e:7b:d3<br><br>eth1: no PHY found - interface inoperative<br><br>RAMDISK driver initialized: 16 RAM disks of 4096K size
1024 blocksize<br><br>Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4<br><br>ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx<br><br>PCMCIA slot B: phys mem e0000000...ec000000 (size 0c000000)<br><br>No card in slot B: PIPR=ff00ff00<br><br>TQM8xxL0: Found 2 x16 devices at 0x0 in 32-bit mode<br><br>TQM8xxL0: Found 2 x16 devices at 0x400000 in 32-bit mode<br><br> Amd/Fujitsu Extended Query Table at 0x0040<br><br>number of CFI chips: 2<br><br>cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.<br><br>TQM flash bank 0: Using static image partition definition<br><br>Creating 7 MTD partitions on "TQM8xxL0":<br><br>0x00000000-0x00040000 : "u-boot"<br><br>0x00040000-0x00100000 : "kernel"<br><br>0x00100000-0x00200000 : "user"<br><br>0x00200000-0x00400000 : "initrd"<br><br>0x00400000-0x00600000 : "cramfs"<br><br>0x00600000-0x00800000 : "jffs"<br><br>0x00400000-0x00800000 : "big_fs"<br><br>NET4: Linux TCP/IP 1.0 for
NET4.0<br><br>IP Protocols: ICMP, UDP, TCP<br><br>IP: routing cache hash table of 512 buckets, 4Kbytes<br><br>TCP: Hash tables configured (established 1024 bind 2048)<br><br>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.<br><br>RAMDISK: Compressed image found at block 0<br><br>Freeing initrd memory: 1587k freed<br><br>VFS: Mounted root (ext2 filesystem).<br><br>VFS: Cannot open root device "" or 00:00<br><br>Please append a correct "root=" boot option<br><br>Kernel panic: VFS: Unable to mount root fs on 00:00<br><br> <0>Rebooting in 180 seconds..<br>///////////////////////////////////////////////////////////////////////////<br>What I miss?May i correct it <br>I also build kernel Linux 2.6.11.7 use tosati patch and config ,but when I want this kernel support virtual terminal it hang.May I correct it?<br>Please help me <br>Thanks<br>LeVan<br><br><br><br><p> Send instant messages to your online friends http://au.messenger.yahoo.com