U-Boot 1.1.4 (Aug 7 2006 - 20:36:40) CPU: AMCC PowerPC 440GX Rev. F at 533.333 MHz (PLB=133, OPB=66, EBC=66 MHz) I2C boot EEPROM enabled Internal PCI arbiter enabled 32 kB I-Cache 32 kB D-Cache Board: Ocotea - AMCC PPC440GX Evaluation Board I2C: ready DRAM: 256 MB FLASH: 5 MB PCI: Bus Dev VenId DevId Class Int In: serial Out: serial Err: serial Net: ppc_4xx_eth0, ppc_4xx_eth1, ppc_4xx_eth2, ppc_4xx_eth3 Sachin " ****************Read ReadMeInstructions: Uboot Environment Variable Configuration *************" Hit any key to stop autoboot: 0 ## Booting image at ffc00000 ... Image Name: Linux-2.6.16.1 Created: 2006-08-02 19:51:26 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 931818 Bytes = 910 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.6.16.1 (root@linux) (gcc version 3.4.1 20040714 (TimeSys 3.4.1-7)) #3 Thu Aug 3 01:21:21 IST 2006 IBM Ocotea port (MontaVista Software, Inc. ) Built 1 zonelists Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.2:/opt/timesys/linux/6.1/ppc440-std/rfs ip=192.168.0.54:192.168.0.2:192.168.0.1:255.255.255.0:ocotea:eth 0::off console=ttyS0,115200 PID hash table entries: 2048 (order: 11, 32768 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 257664k available (1420k kernel code, 460k data, 112k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 PCI: Probing PCI hardware io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at MMIO 0x0 (irq = 0) is a 16550A serial8250: ttyS1 at MMIO 0x0 (irq = 1) is a 16550A PPC 4xx OCP EMAC driver, version 3.54 mal0: initialized, 4 TX channels, 4 RX channels zmii0: bridge in SMII mode eth0: emac0, MAC 00:01:73:01:de:c8 eth0: found Generic MII PHY (0x01) eth1: emac1, MAC 00:01:73:01:de:c9 eth1: found Generic MII PHY (0x02) rgmii0: input 0 in RGMII mode eth2: emac2, MAC 00:01:73:01:de:ca eth2: found CIS8201 Gigabit Ethernet PHY (0x10) rgmii0: input 1 in RGMII mode eth3: emac3, MAC 00:01:73:01:de:cb eth3: found CIS8201 Gigabit Ethernet PHY (0x18) mice: PS/2 mouse device common for all mice NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 4, 65536 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 eth0: link is down IP-Config: Complete: device=eth0, addr=192.168.0.54, mask=255.255.255.0, gw=192.168.0.1, host=ocotea, domain=, nis-domain=(none), bootserver=192.168.0.2, rootserver=192.168.0.2, rootpath= Looking up port of RPC 100003/2 on 192.168.0.2 eth0: link is up, 100 FDX, pause enabled Looking up port of RPC 100005/1 on 192.168.0.2 VFS: Mounted root (nfs filesystem). Freeing unused kernel memory: 112k init INIT: version 2.84 booting Welcome to Distribution built using LinuxLink by TimeSys (6.1) mounting... ramfs at /dev Creating initial udev device nodes: making extra nodes udev startup is finished! Initializing hardware... storage network audio done[ OK ] raidautorun: failed to open /dev/md0: 6 Configuring kernel parameters: [ OK ] Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Setting clock : Mon Apr 6 08:19:06 UTC 2015 [ OK ] Setting hostname timesys-bsp: [ OK ] Your system appears to have shut down uncleanly Press Y within 1 seconds to force file system integrity check... Remounting root filesystem in read-write mode: [ OK ] Checking filesystems Checking all file systems. [ OK ] chown: changing ownership of `/tmp/.ICE-unix': Operation not permitted Enabling swap space: [ OK ] INIT: Entering runlevel: 3 Entering non-interactive startup Setting network parameters: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Starting portmap: [ OK ] Starting NFS statd: [ OK ] Starting xinetd: [ OK ] Starting crond: [ OK ] Starting atd: [ OK ] Starting system message bus: [ OK ] Starting the Alphion Demo App Starting alphiondemo ************* Alphion Demo APP Started ********************* ************* This is a sample Demo to start and stop apps ******** Done Distribution built using LinuxLink by TimeSys (6.1) Kernel 2.6.16.1 for ppc timesys-bsp login: root Last login: Mon Apr 6 06:33:48 on ttyS0 -bash-2.05b# lsmod Module Size Used by -bash-2.05b# **************************************After L Alphion Wake after a minute ..... -bash: ********************: command not found -bash-2.05b# -bash-2.05b# -bash-2.05b# ps -ax | grep alphion Warning: bad ps syntax, perhaps a bogus '-'? See http://procps.sf.net/faq.html 352 ? S 0:00 /home/AlphionApps//alphiondemo 383 ttyS0 R+ 0:00 grep alphion -bash-2.05b# kill -9 352 -bash-2.05b# ************************************* output of lsmod ************* -bash: *************************************: command not found -bash-2.05b# ************************************* output of lsmod ************* -bash-2.05b# -bash-2.05b# -bash-2.05b# lsmod Module Size Used by -bash-2.05b# -bash-2.05b# -bash-2.05b# -bash-2.05b# -bash-2.05b# -bash-2.05b# *************Inserting the Modules ************* -bash: *************Inserting: command not found -bash-2.05b# -bash-2.05b# insmod i2c-dev.ko insmod: can't read 'i2c-dev.ko': No such file or directory -bash-2.05b# cd /lib/modules/2.6.16.1/kernel/drivers/i2c/ -bash-2.05b# insmod i2c-dev.ko i2c_dev: Unknown symbol i2c_check_addr i2c_dev: Unknown symbol i2c_get_adapter i2c_dev: Unknown symbol i2c_control i2c_dev: Unknown symbol i2c_master_recv i2c_dev: Unknown symbol i2c_smbus_xfer i2c_dev: Unknown symbol i2c_register_driver i2c_dev: Unknown symbol i2c_put_adapter i2c_dev: Unknown symbol i2c_transfer i2c_dev: Unknown symbol i2c_del_driver i2c_dev: Unknown symbol i2c_master_send insmod: error inserting 'i2c-dev.ko': -1 Unknown symbol in module -bash-2.05b# insmod i2c-core.ko -bash-2.05b# lsmod Module Size Used by i2c_core 22384 0 -bash-2.05b# insmod i2c-dev.ko -bash-2.05b# lsmod Module Size Used by i2c_dev 10116 0 i2c_core 22384 1 i2c_dev -bash-2.05b# ls algos busses chips i2c-core.ko i2c-dev.ko -bash-2.05b# cd chips/ -bash-2.05b# insmod insmod insmod.static insmod_ksymoops_clean -bash-2.05b# insmod eeprom.ko -bash-2.05b# lsmod Module Size Used by eeprom 6736 0 i2c_dev 10116 0 i2c_core 22384 2 eeprom,i2c_dev -bash-2.05b# ls ds1337.ko eeprom.ko max6875.ko pcf8574.ko rtc8564.ko ds1374.ko m41t00.ko pca9539.ko pcf8591.ko x1205.ko -bash-2.05b# cd .. -bash-2.05b# ls algos busses chips i2c-core.ko i2c-dev.ko -bash-2.05b# cd busses/ -bash-2.05b# ls i2c-ali1535.ko i2c-i801.ko i2c-pca-isa.ko i2c-sis96x.ko i2c-ali1563.ko i2c-i810.ko i2c-piix4.ko i2c-stub.ko i2c-ali15x3.ko i2c-ibm_iic.ko i2c-prosavage.ko i2c-via.ko i2c-amd756-s4882.ko i2c-mpc.ko i2c-savage4.ko i2c-viapro.ko i2c-amd756.ko i2c-nforce2.ko i2c-sis5595.ko i2c-voodoo3.ko i2c-amd8111.ko i2c-parport-light.ko i2c-sis630.ko scx200_acb.ko -bash-2.05b# insmod 2c-ibm_iic.ko insmod: can't read '2c-ibm_iic.ko': No such file or directory -bash-2.05b# insmod i2c-ibm_iic.ko -bash-2.05b# lsmod Module Size Used by i2c_ibm_iic 7432 0 eeprom 6736 0 i2c_dev 10116 0 i2c_core 22384 3 i2c_ibm_iic,eeprom,i2c_dev