######## For 2.4.25 kernel from Freescale ################## U-Boot 1.1.3 (Freescale) (May 17 2006 - 08:00:07) CPU: MPC5200 v2.2 at 396 MHz Bus 132 MHz, IPB 132 MHz, PCI 33 MHz Board: Freescale MPC5200 (Lite5200B) I2C: 85 kHz, ready DRAM: 64 MB Top of RAM usable for U-Boot at: 04000000 Reserving 524k for U-Boot at: 03f7c000 Reserving 191k for malloc() at: 03f4c008 Reserving 68 Bytes for Board Info at: 03f4bfc4 Reserving 56 Bytes for Global Data at: 03f4bf8c Stack Pointer at: 03f4bf68 New Stack Pointer is: 03f4bf68 Now running in RAM - U-Boot at: 03f7c000 FLASH: Flash does not respond to CFI commands flash_protect ON: from 0xFF000000 to 0xFF038FFF protect on 0 protect on 1 protect on 2 protect on 3 flash_protect ON: from 0xFF040000 to 0xFF04FFF7 protect on 4 16 MB basetask = 0, tasks = 2 task_org = 0x03fb3000 TDT start = 0x00000040, end = 0x000001b8 U-Boot : Doing PCI Initialization for MPC5200B PCI: Bus Dev VenId DevId Class Int PCI: Bus Dev VenId DevId Class Int PCI Scan: Found Bus 0, Device 24, Function 0 00 18 1057 5809 0680 00 PCI Scan: Found Bus 0, Device 26, Function 0 PCI Scan: Found Bus 1, Device 8, Function 0 01 08 104c 9065 ff00 00 00 1a 104c ac23 0604 ff In: serial Out: serial Err: serial U-Boot relocated to 03f7c000 ### main_loop entered: bootdelay=5 ### main_loop: bootcmd="run nfsargs addip;tftp 1000000 /tftpboot/uImage;bootm 1000000" Hit any key to stop autoboot: 5  4  3  2  1  0 Net: mpc5xxx_fec_init_phy... Begin mpc5xxx_fec_init_phy... Done FEC ETHERNET Trying FEC ETHERNET mpc5xxx_fec_init... Begin mpc5xxx_fec_init_phy_complete... Begin mpc5xxx_fec_init_phy_complete... Done mpc5xxx_fec_init... Done Using FEC ETHERNET device TFTP from server 10.50.40.203; our IP address is 10.50.40.201 Filename '/tftpboot/uImage'. Load address: 0x1000000 Loading: ############################################################################# ############################################################################# ############################################################################# ############################################################################# ######################### done Bytes transferred = 1000192 (f4300 hex) Ethernet task stopped ## Booting image at 01000000 ... Image Name: Linux-2.4.25 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1000128 Bytes = 976.7 kB Load Address: 00000000 Entry Point: 00000000 Uncompressing Kernel Image ... OK ## Current stack ends at 0x03F4BBB8 => set upper limit to 0x00800000 ## cmdline at 0x007FFF00 ... 0x007FFF9E bd address = 0x03F4BFC4 memstart = 0x00000000 memsize = 0x04000000 flashstart = 0xFF000000 flashsize = 0x01000000 flashoffset = 0x00039000 sramstart = 0x00000000 sramsize = 0x00000000 bootflags = 0x00000001 intfreq = 396 MHz busfreq = 132 MHz ethaddr = 00:04:9F:AA:BB:CC IP addr = 10.50.40.201 baudrate = 115200 bps No initrd ## Transferring control to Linux (at address 00000000) ... Memory BAT mapping: BAT2=64Mb, BAT3=0Mb, residual: 0Mb Linux version 2.4.25 (root@localname) (gcc version 3.3.2) #22 Tue Jul 4 05:22:54 UTC 2006 On node 0 totalpages: 16384 zone(0): 16384 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: console=ttyS0,115200 root=/dev/nfs nfsroot=10.50.40.203:/tftpboot/5200B_test/rootfsdir ip=10.50.40.201:10.50.40.203:10.50.40.1:255.255.248.0::eth0:off panic=1 Console: colour dummy device 80x25 Calibrating delay loop... 263.78 BogoMIPS Memory: 61928k available (1672k kernel code, 552k data, 96k init, 0k highmem) Dentry cache hash table entries: 8192 (order: 4, 65536 bytes) Inode cache hash table entries: 4096 (order: 3, 32768 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 4096 (order: 2, 16384 bytes) Page-cache hash table entries: 16384 (order: 4, 65536 bytes) POSIX conformance testing by UNIFIX PCI: Probing PCI hardware pcibios_fixup_bus <1>: res->start = 50001000, res->end = 50001fff pcibios_fixup_bus <1>: res->start = 40000000, res->end = 40ffffff pcibios_fixup_bus <1>: res->start = 10000000, res->end = 100fffff pcibios_fixup_bus <1>: res->start = 0, res->end = 0 PCI: bridge rsrc 50000000..50ffffff (100), parent c01dffd0 PCI: bridge rsrc 40000000..4fffffff (200), parent c01dffec PCI: bridge rsrc 50001000..50001fff (101), parent c02d5038 PCI: bridge rsrc 40000000..40ffffff (200), parent c02d5054 PCI: bridge rsrc 10000000..100fffff (1200), parent 00000000 PCI: Cannot allocate resource region 2 of PCI bridge 1 PCI: bridge 1 resource 2 moved to 4ff00000..4fffffff PCI: Cannot allocate resource region 0 of device 00:18.0 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Installing knfsd (copyright (C) 1996 okir@monad.swb.de). JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc. i2c-core.o: i2c core module version 2.6.1 (20010830) i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830) i2c-proc.o version 2.6.1 (20010830) MB86290: fb_init called. MB86290: initialize called. MB86290: pci_find_device failed(10cf, 2019). MB86290: get pci addr failed. MB86290: initialize_gdc failed. MB86290: initialize_gdc failed. pty: 256 Unix98 ptys configured ttyS0 on PSC1 ttyS1 on PSC2 ttyS2 on PSC3 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Port Config is: 0x10050004 ipb=132MHz, set clock period to 7 GPIO config: 11050004 ATA invalid: 01000000 ATA hostcnf: 03000000 ATA pio1 : 100a0a00 ATA pio2 : 02040600 XLB Arb cnf: 0000a366 mpc5xxx_ide: Setting up IDE interface ide0... Probing IDE interface ide0... SCSI subsystem driver Revision: 1.00 Icecube Bank 0: Found 1 x16 devices at 0x0 in 8-bit mode Amd/Fujitsu Extended Query Table at 0x0040 Icecube Bank 0: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Icecube flash bank 0: Using static image partition definition Creating 5 MTD partitions on "Icecube Bank 0": 0x00000000-0x00040000 : "Bootloader" 0x00040000-0x00050000 : "Environment" 0x00050000-0x00e00000 : "Filesystem" 0x00e00000-0x00f00000 : "Kernel" 0x00f00000-0x01000000 : "dBUG" usb.c: registered new driver usbdevfs usb.c: registered new driver hub host/usb-ohci.c: USB OHCI at membase 0xf0001000, IRQ 44 host/usb-ohci.c: usb-0, Built-In ohci usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb.c: registered new driver usbmouse usbmouse.c: v1.6:USB HID Boot Protocol mouse driver usb.c: registered new driver usbkbd usbkbd.c: :USB HID Boot Protocol keyboard driver Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c-icecube.o: I2C module #2 installed NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 4096 bind 8192) eth0: Phy @ 0x0, type LXT971 (0x001378e2) IP-Config: Complete: device=eth0, addr=10.50.40.201, mask=255.255.248.0, gw=10.50.40.1, host=10.50.40.201, domain=, nis-domain=(none), bootserver=10.50.40.203, rootserver=10.50.40.203, rootpath= NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Looking up port of RPC 100003/2 on 10.50.40.203 Looking up port of RPC 100005/1 on 10.50.40.203 VFS: Mounted root (nfs filesystem). Freeing unused kernel memory: 96k init hub.c: new USB device 0-1, assigned address 2 usb.c: USB device not accepting new address=2 (error=-110) Setting hostname hostname: /etc/hostname: No such file or directory Setting Date Wed Sep 10 00:00:00 GMT 2003 Mounting proc Remounting rootfs r/w Mounting sysfs hub.c: new USB device 0-1, assigned address 3 usb.c: USB device not accepting new address=3 (error=-110) mount: Mounting sysfs on /sys failed: No such device *** Running rc.modules *** Running rc.serial *** Attempting to start S15inet Starting inetd Done *** Attempting to start S20network Setting up link for loopback Done Setting up link for eth0 SIOCSIFNETMASK: Invalid argument RTNETLINK answers: File exists FAILED *** Attempting to start S23portmap Starting rpc.portmap Done *** Attempting to start S30ftp Starting in.ftpd Done *** Attempting to start S30vsftpd Starting vsftpd Done *** Attempting to start S90boa bind: Address already in use *** Running rc.local 10.50.40.201 login: root login[39]: root login on `ttyS0' # # # # # # cat /proc/bus/pci/devices 00c0 10575809 0 00000000 00000008 00000000 00000000 00000000 00000000 00000000 00040000 40000000 00000000 00000000 00000000 00000000 00000000 00d0 104cac23 0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 0140 104c9065 0 40000008 40800000 50001001 00000000 00000000 00000000 00000000 00400000 00800000 00000010 00000000 00000000 00000000 00000000 #